3000GT / Stealth EVOSPEC Drive By Wire Pedal Adapter

Here is an adapter bracket made for the 3KGT – GTO – Stealth platform to allow you to use the Evo X DBW accelerator pedal for a bolt on DBW setup. This bracket puts the Evo X pedal in the factory location. The bracket is also adjustable (left to right) to also give the end user a little bit of adjustability to fit your needs. We chose the Evo X pedal because they are cheap, very available, and offer good resolution over some other DBW pedals. Each bracket setup will INCLUDE all titanium hardware to bolt the bracket to the firewall and the pedal to the bracket. Also an optional choice Evo X DBW pedal connector with pins and seal AND Bosch DBW throttle body connector.

OEM Mitsubishi DBW pedal is available with limited supply (When selecting the OEM Mitsubishi DBW pedal if it is shown as an option, it is in stock. If it is not shown in options it is not in stock. These are good used pedals from the EvoX or Ralliart.)

Available in Raw and Anodized finish.

Also an additional option is a complete DBW PNP harness that you will pin to your ecu. We have teamed up with Raven Fabrication exclusively make  DBW harnesses for our kits. We chose Raven Fabrication for this project because they offer some of the highest quality harnesses in the Mitsubishi platform game and understand custom work of the highest level. These harnesses are mostly plug and play other then the end user pinning the pins to your ecu/ecu harness. One end connects to your chosen TB, another end connects to the Mitsubishi DBW pedal, and the other end connects to your ecu. Each harness has a super small quick disconnect connector that fits through your oem Throttle cable hole or any other hole you chose to pass it through on the firewall making it super simple to install.

Some benefits to going DBW

• Deletes the factory throttle cable cleaning up the engine bay
• Eliminates the need for a Idle Air Control Valve
• Improved Driveability when using larger sized Throttle Bodies.
• Easier Part-Throttle tuning for a smoother part throttle response while driving
• ECU controlled Launch control
• REV-MATCHED tuning Downshifts and No-lift upshift shifting.
• Traction Control assistance using throttle position.
• Cruise Control and Valet mode for safety.

Known ECU’s that support DBW :

HALTECH
Elite 1500
Elite 2000
Elite 2500
Nexus R5

AEM
Infinity – 6
Infinity – 8
Infinity -8H

Fuel Tech
FT 550 lite
FT 550
FT 600

LINK ECU
G4X Extreme X
G4X Fury X
G4X Plug in X
G4+ Force GDI
G4+ Thunder

MOTEC
ALL M1 Series

PROEFI
Pro 70
Pro 112
Pro 128

ECU MASTER
EMU – Black
EMU – Classic

MAXX ECU
Sport
Race
Pro

NOTE: This does NOT work with Stock, Flash, Chrome ECU nor AEM Series 1 and Series 2 ECUs

COMPATIBLE DBW THROTTLE BODYs and INFO:

Bosch DBW Throttle body.
Note the 68mm TB mounting holes need to be drilled out for M8 sized bolts.
The 82mm TB will require a adapter flange or a intake manifold flanged for this TB.
These will require the Bosch connector which you can choose in the connector drop down window.

Bosch DBW TB
. 68MM TB
PN 0280750156
. 82MM TB PN
0280750473

OEM Mitsubishi DBW options.
Note these are a direct bolt on to your EVO, DSM, and 3000GT OEM intake manifolds. Make sure you port match your manifold to the TB if needed. These will require the Mitsubishi connector which you can choose in the connector drop down window

2005 / 2012 Eclipse GT 68mm DBW TB

60mm The 4g eclipse NON gt 2.4L, 04-06 Lancer Ralliart, 05-06 4cyl Outlander, 05 – 12 Galant (4 cyl)

The bosch throttle bodies are sometimes on backorder, for stock status on those contact us.